exported markdown

Cube_Operators_Log.md

@@ -0,0 +1,62 @@
+**When you use the Cube, please add notes here. Newest at top.**
+
+- Operational at Makersmiths. Seems to print a RasPi case fine.
+  [Mirage335](User:Mirage335 "wikilink")
+  ([talk](User_talk:Mirage335 "wikilink")) 11:27, 8 April 2016 (PDT)
+
+<!-- -->
+
+- Printed Reprap Wilson Z Brace. Failed becuase cartridge ran out of
+  filament. Refilled filament making sure not to wind it too tightly
+  (Did by hand). Also made sure to release tension on wound filament
+  very few winds by counter rotation cartridge.
+  --[Nostromo](User:Nostromo "wikilink")
+  ([talk](User_talk:Nostromo "wikilink")) 16:45, 16 April 2015 (PDT)
+
+<!-- -->
+
+- James reports: Attempted to print LCD Knob for Reprap Wilson but
+  printer refused to start printing with a "Cartridge Empty" error
+  message. Need to procure another cartridge and being doing cartridge
+  swap procedure to bypass this check.
+  --[Nostromo](User:Nostromo "wikilink")
+  ([talk](User_talk:Nostromo "wikilink")) 09:52, 13 March 2015 (PDT)
+
+<!-- -->
+
+- James reports: Printed Y bearing holders from Prusa Mendel upgrade.
+  New mirrored build surface is working well with Elmers glue stick
+  (Easier to release parts). Several failed attempts at printing
+  filament bypass for cube because of poor STL file orientation.
+  --[Nostromo](User:Nostromo "wikilink")
+  ([talk](User_talk:Nostromo "wikilink")) 09:34, 1 March 2015 (PST)
+
+<!-- -->
+
+- James reports: Printer is operating well. There is slight warping of
+  larger 4 inch parts on the corners but prints complete successfully.
+  The part I was printing failed in a strange way (printed part was
+  missing a geometric section). This might be due to forgetting to run
+  heal in the software. Also when transferring the .cube file to the
+  printer just use the USB key as it is far more reliable than the wifi.
+  --[Nostromo](User:Nostromo "wikilink")
+  ([talk](User_talk:Nostromo "wikilink")) 13:49, 11 February 2015 (PST)
+
+<!-- -->
+
+- James reports: Performed Bed Leveling procedure (Ugh!!). Printing
+  Wilson Piecemeal Y Idler. The print looks a little smooshed on the
+  bottom. Consider recalibrating Z a little higher.
+  --[Nostromo](User:Nostromo "wikilink")
+  ([talk](User_talk:Nostromo "wikilink")) 17:36, 5 February 2015 (PST)
+
+<!-- -->
+
+- James reports: Printed 2nd part on this printer. Reset Z axis to 1.60z
+  so that it wouldn't smoosh the part as much. seemes to have worked but
+  has a little bit of warping of the edges of the 5" part I was
+  printing. Removing the part is requiring long times in a water bath to
+  permeate the glue underneath --[Nostromo](User:Nostromo "wikilink")
+  ([talk](User_talk:Nostromo "wikilink")) 16:01, 8 February 2015 (PST)
+
+[Category:Cube](Category:Cube "wikilink")