279 lines
6.8 KiB
INI
279 lines
6.8 KiB
INI
# This file contains common pin mappings for RAMBo boards. To use this
|
|
# config, the firmware should be compiled for the AVR atmega2560.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
[gcode_macro CALIBRATE_NOZZLE_OFFSET]
|
|
description: Move to center of bed and calibrate nozzle offset
|
|
gcode:
|
|
G90
|
|
G0 X100 Y155 F1500
|
|
PROBE_CALIBRATE
|
|
|
|
[gcode_macro LEVEL_BED]
|
|
description: "Level the bed manually."
|
|
gcode:
|
|
BED_SCREWS_ADJUST
|
|
|
|
[gcode_macro CHECK_DEVIATION]
|
|
description: "Check the deviation of the bed from the last loaded mesh."
|
|
gcode:
|
|
SCREWS_TILT_CALCULATE MAX_DEVIATION=0.05
|
|
|
|
[gcode_macro LIZ_IS_A_BAKA]
|
|
description: "Liz is a baka, so here's her start G-Code >.<"
|
|
gcode:
|
|
BED_MESH_CALIBRATE
|
|
BED_MESH_PROFILE SAVE=default
|
|
|
|
[gcode_macro _START_GCODE]
|
|
description: "The gcode that should be called from your slicer at the beginning of a print."
|
|
gcode:
|
|
# Ender 3 Custom Start G-code
|
|
G90
|
|
G1 X2 Y30 Z30 F1500
|
|
G1 Z0.28 F240
|
|
G92 E0
|
|
G1 Y220 E10 F1500 ; prime the nozzle
|
|
G1 X2.3 F5000
|
|
G92 E0
|
|
G1 Y30 E10 F1200 ; prime the nozzle
|
|
G92 E0
|
|
G1 Z5 F1500 ; don't scratch the build plate
|
|
|
|
[gcode_macro _END_GCODE]
|
|
description: "The gcode that should be called from your slicer at the end of a print."
|
|
gcode:
|
|
G91 # Relative positioning
|
|
G1 E-2 F2700 # Retract a bit
|
|
G1 E-2 Z0.2 F2400 # Retract and raise Z
|
|
G1 X5 Y5 F3000 # Wipe out
|
|
G1 Z10 # Raise Z more
|
|
G90 # Absolute positioning
|
|
|
|
G1 X0 Y220 # Present print
|
|
M106 S0 # Turn-off fan
|
|
M104 S0 # Turn-off hotend
|
|
M140 S0 # Turn-off bed
|
|
|
|
M84 X Y E # Disable all steppers but Z
|
|
|
|
[stepper_x]
|
|
step_pin: PC0
|
|
dir_pin: PL1
|
|
enable_pin: !PA7
|
|
microsteps: 16
|
|
# rotation_distance: 40 # Default, seems 3mm short on a 10mm move
|
|
# rotation_distance: 28 # Test 1, seems to move 1-2mm too far
|
|
# rotation_distance: 30 # Test 2, seems to move 1mm too far
|
|
rotation_distance: 33
|
|
endstop_pin: ^!PB6
|
|
#endstop_pin: ^PA2
|
|
position_endstop: 0
|
|
position_max: 298
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PC1
|
|
dir_pin: !PL0
|
|
enable_pin: !PA6
|
|
microsteps: 16
|
|
# rotation_distance: 40 # Default, Seems 4mm overshot
|
|
# rotation_distance: 42 # Test 1, Still seems 3-4mm overshot
|
|
rotation_distance: 46
|
|
endstop_pin: ^!PB5
|
|
#endstop_pin: ^PA1
|
|
position_endstop: 0
|
|
position_max: 280
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PC2
|
|
dir_pin: PL2
|
|
enable_pin: !PA5
|
|
microsteps: 16
|
|
# rotation_distance: 8 # Default, seems 1mm too short
|
|
# rotation_distance: 7.2 # Test 1, seems 3mm overshot
|
|
# rotation_distance: 8.33 # Test 2, still seems 1mm under
|
|
rotation_distance: 8
|
|
endstop_pin: probe:z_virtual_endstop
|
|
#endstop_pin: !PB4
|
|
#endstop_pin: ^PC7
|
|
# position_endstop: 0.5
|
|
position_max: 250
|
|
|
|
[bltouch]
|
|
sensor_pin: ^PB4
|
|
control_pin: PL5
|
|
x_offset: -44
|
|
y_offset: 8
|
|
#z_offset: 3.0
|
|
|
|
[bed_mesh]
|
|
speed: 120
|
|
horizontal_move_z: 7
|
|
mesh_min: 30, 40
|
|
mesh_max: 250, 230
|
|
probe_count: 5
|
|
mesh_pps: 3
|
|
algorithm: bicubic
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 140, 140
|
|
speed: 50
|
|
z_hop: 10
|
|
z_hop_speed: 5
|
|
|
|
[extruder]
|
|
step_pin: PC3
|
|
dir_pin: PL6
|
|
enable_pin: !PA4
|
|
microsteps: 16
|
|
# rotation_distance: 33.500 # Original Setting, seems ??x too small
|
|
# rotation_distance: 16.75 # Initial test, seems to extrude 1/2 supposed
|
|
# rotation_distance: 8.375 # Test Two, still seems 1/2
|
|
# rotation_distance: 4.25 # Old Extruder Setup
|
|
rotation_distance: 7.9797 # Copied from Replimat
|
|
nozzle_diameter: 0.400
|
|
heater_pin: PH6
|
|
# filament_diameter: 2.850
|
|
filament_diameter: 1.750
|
|
# sensor_type: EPCOS 100K B57560G104F # Either it's not connecting right, or this is the wronf sensor
|
|
sensor_type: NTC 100K MGB18-104F39050L32 # Probably just disconnected
|
|
sensor_pin: PF0
|
|
#control: pid
|
|
#pid_Kp: 22.2
|
|
#pid_Ki: 1.08
|
|
#pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 990
|
|
|
|
#[extruder1]
|
|
#step_pin: PC4
|
|
#dir_pin: PL7
|
|
#enable_pin: !PA3
|
|
#heater_pin: PH4
|
|
#sensor_pin: PF1
|
|
#...
|
|
|
|
[heater_bed]
|
|
heater_pin: PE5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PF2
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
max_power: 1.0
|
|
|
|
[verify_heater heater_bed]
|
|
heating_gain: 1
|
|
check_gain_time: 60
|
|
|
|
[fan]
|
|
pin: PH3
|
|
|
|
[heater_fan heatbreak_cooling_fan]
|
|
pin: PH5
|
|
fan_speed: 1.0
|
|
# The fan speed (expressed as a value from 0.0 to 1.0) that the fan
|
|
# will be set to when its associated heater is enabled. The default
|
|
# is 1.0
|
|
#max_power:
|
|
#shutdown_speed:
|
|
#cycle_time:
|
|
#hardware_pwm:
|
|
#kick_start_time:
|
|
#off_below:
|
|
#tachometer_pin:
|
|
#tachometer_ppr:
|
|
#tachometer_poll_interval:
|
|
#enable_pin:
|
|
# See the "fan" section for a description of the above parameters.
|
|
heater: extruder
|
|
# Name of the config section defining the heater that this fan is
|
|
# associated with. If a comma separated list of heater names is
|
|
# provided here, then the fan will be enabled when any of the given
|
|
# heaters are enabled. The default is "extruder".
|
|
heater_temp: 50.0
|
|
# A temperature (in Celsius) that the heater must drop below before
|
|
# the fan is disabled. The default is 50 Celsius.
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-UltiMachine__ultimachine.com__RAMBo_6403335373035101E171-if00
|
|
baud: 250000
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[ad5206 stepper_digipot]
|
|
enable_pin: PD7
|
|
# Scale the config so that the channel value can be specified in amps.
|
|
# (For Rambo v1.0d boards, use 1.56 instead.)
|
|
scale: 2.08
|
|
# Channel 1 is E0, 2 is E1, 3 is unused, 4 is Z, 5 is X, 6 is Y
|
|
channel_1: 1.34
|
|
channel_2: 1.0
|
|
channel_4: 1.1
|
|
channel_5: 1.1
|
|
channel_6: 1.1
|
|
|
|
# Enable 16 micro-steps on steppers X, Y, Z, E0, E1
|
|
[static_digital_output stepper_config]
|
|
pins:
|
|
PG1, PG0,
|
|
PK7, PG2,
|
|
PK6, PK5,
|
|
PK3, PK4,
|
|
PK1, PK2
|
|
|
|
[static_digital_output yellow_led]
|
|
pins: !PB7
|
|
|
|
# Common EXP1 / EXP2 (display) pins
|
|
[board_pins]
|
|
aliases:
|
|
# Common EXP1/EXP2 headers found on RAMBo v1.4
|
|
EXP1_1=PE6, EXP1_3=PG3, EXP1_5=PJ2, EXP1_7=PJ7, EXP1_9=<GND>,
|
|
EXP1_2=PE2, EXP1_4=PG4, EXP1_6=PJ3, EXP1_8=PJ4, EXP1_10=<5V>,
|
|
# EXP2 header
|
|
EXP2_1=PB3, EXP2_3=PJ5, EXP2_5=PJ6, EXP2_7=PD4, EXP2_9=<GND>,
|
|
EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PE7, EXP2_10=PH2
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
[include mainsail.cfg]
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [bltouch]
|
|
#*# z_offset = 2.850
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# -1.065000, -0.857500, -0.817500, -0.865000, -0.927500
|
|
#*# -0.592500, -0.502500, -0.442500, -0.482500, -0.522500
|
|
#*# -0.172500, -0.070000, -0.027500, -0.040000, -0.057500
|
|
#*# 0.182500, 0.265000, 0.312500, 0.302500, 0.332500
|
|
#*# 0.480000, 0.610000, 0.670000, 0.715000, 0.735000
|
|
#*# x_count = 5
|
|
#*# y_count = 5
|
|
#*# mesh_x_pps = 3
|
|
#*# mesh_y_pps = 3
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 30.0
|
|
#*# max_x = 250.0
|
|
#*# min_y = 39.989999999999995
|
|
#*# max_y = 230.0
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 23.769
|
|
#*# pid_ki = 1.248
|
|
#*# pid_kd = 113.201
|